Hello! I'm in a new situation now where I need to be able to move my grow tent almost daily. Cord lengths aren't an issue, but a 4x4x7ft tent with all the equipment weighs a lot. Does anyone have any ideas for how I might go about this? I want to avoid wooden pallets because it is indoors. I also have about a foot and a half of room above the tent, so I can use larger caster wheels if I have to.
Announcement
Collapse
No announcement yet.
Casters for a grow tent ideas.
Collapse
X
-
Check out my post Number 21.
Simple grow room gadgets that make you life easier - GrowWeedEasy.com Cannabis Growing ForumRaygun is hip-hop.
Coco/perlite
3x3x6
- Likes 2
Comment
-
Last spring I made some platforms for my tents to elevate them before I I had water in my basement, like I did this past weekend. I used 3/4 in plywood and some blocks of 2x4s in the corners and in the middle for elevation and support. The tent with the blue zipper is 3x4 feet, and the other is 3x3. I put a block in each corner and middle of each side as well as the center. For the 3x4 I used a little longer blocks in the middle and center. The end product is very sturdy, and I have stood inside the tents on these platforms and no sagging or cracking of the wood. I have also (carefully) dragged these around the concrete floor with fully loaded tents on top without issue. You could mount some casters on these and easily wheel them around.
1 Photo
- Likes 2
Comment
-
Rootsruler is onto something. It's an interesting problem to have...needing to move the grow tent, daily. I'd think simple is better. If you go the plywood route as suggested be sure to get 3/4". The casters will serve you best if you get something rated for heavy weight. I have a hybrid table saw on casters. It's easy to move. Also consider whether you want your casters to swivel. 4 that swivel 360 would make the tent as maneuverable as possible. I'm guessing with 1 1/2' of overhead space ceiling fans are not an issue? Is relocating the tent the only option?Auto/Photo Tent: Gorilla 2x4x7'11" HLG 350R, Infinity 4" w/Carbon Filter, Coco 50/50 perlite
Autopot system: 1 Scarlet Grapes & 1 Scarlet Sunset
Photo Tent: Gorilla 4x4x7'11" HLG Scorpion R, Infinity 6” w/Carbon Filter, Coco 50/50 perlite, Autopot system: Idle at the moment
Nutrients: CX Horticulture - full line for both tents
Comment
-
He probably wants it so that he has better access to all sides of his tent. I have the same issue. My tent is in the corner of my office so I only have access to 2 sides.
I was going to build the same type of platform but instead of moving the whole tent for access I took an old pneumatic office chair, removed the casters, removed the back support and seat bottom from the piston and base and placed it in the middle of the tent. Whenever I need access to an area that is hard to reach due to my limited access I attach the seat bottom to the piston and lay on it giving me full access to the entire canopy from above. As the plants get taller I adjust the piston height.
-
-
Originally posted by golfnrl View PostRootsruler is onto something. It's an interesting problem to have...needing to move the grow tent, daily. I'd think simple is better. If you go the plywood route as suggested be sure to get 3/4". The casters will serve you best if you get something rated for heavy weight. I have a hybrid table saw on casters. It's easy to move. Also consider whether you want your casters to swivel. 4 that swivel 360 would make the tent as maneuverable as possible. I'm guessing with 1 1/2' of overhead space ceiling fans are not an issue? Is relocating the tent the only option?
Comment
-
Just make sure the platform can support yours and whatever plants and gear weight that's in the middle so it doesn't sag. I suggest another caster in the middle to support and 3/4" plywood for rigidity. On Amazon they sell a 12 pack of polyurethane casters with flat plate mounts for $25. You can put as many as you feel necessary to support the base.
-
Comment