What's new
By:
GrowWeedEasy.com
You're browsing as a guest. Sign up to join the conversation, share your grows, and get help from thousands of fellow growers — it's free and takes less than a minute.

HYDRO Water acidification with plants in flower - air pump inside the growing space

F

FlyingDutchPaddy

New member
Hi all,

This topic/question might be especially of interest to those growing with hydroponic / DWC setups.

Since switching my lighting over to 12/12 from 24/0 3 weeks ago I've had a struggle controlling water pH levels to keep them within range.
I've observed times where before lights out, pH would be around 6.2 and after 13 hours darkness pH would drop to 5.6. I've even seen 4.8 after 20 hours since last check.

Some background.
From: http://scienceline.ucsb.edu/getkey.php?key=826
"At night, when photosynthesis is not happening, they give off much more CO[SUB]2[/SUB] than they absorb."

From: http://ion.chem.usu.edu/~sbialkow/Classes/3650/Carbonate/Carbonic Acid.html
"[FONT=Verdana,Arial,Helvetica,sans-serif]The most common source of acidity in water is dissolved carbon dioxide."[/FONT]

With hydropinic/DWC setups most (all of us really) have some kind of system to aerate the water (typically an air pump with airstones attached bubbling air into the buckets/totes/reservoirs).

In my particular setup, I have the air pump inside my tent, with the air inlet taking air from inside the tent.

The other day the question came to me: Would the CO2 released by the plants overnight be causing the water pH to drop by such considerable amounts?
Some googling later I found the second link mentioned above.

Overnight the plants release CO2, this gets taken in by the air pump and the (higher than usual in the growing space) CO2 amounts are bubbled into the water creating [FONT=Verdana,Arial,Helvetica,sans-serif]carbonic acid which by itself would have a pH = 5.65.

I think that those of use already adjusting the water pH down after mixing nutrients would see this affecting the pH even more so over time.[/FONT]

My question to you guys:
If you've seen this problem before, how did you solve it?


Have any of you considered using a hose to let the air pump take fresh air from outside the grow space to bubble into the water, or have your air pump outside the grow space to pump it in with longer air tubes?

To test this idea I've taken a hose long enough to allow the airpump to draw intake air from outside the tent.

Will follow up with what I observe over a longer period of time.
 
Co2 does influence ph. But not by that much. Maybe by like 1/100th. So negligible for hydro purposes.
Do you have a new system? New plastic takes time for the PH to stabilize. Once more buffers are added the PH should get into control.
Yes, run the air tubes from outside the tent to the buckets into them. That’s the best way to do it.
 
  • Like
Reactions: DW2
My oh is mostly just affected by my water temp is found out seems to hover around where my water temps are so before I got the water cooler the temps would skyrocket when the lights came on along with the ph same as when it went off after it went off my phone would drop lucky I'm in a hot area so only had to worry about it getting to high but if my water temps were 68 degrees my phone would be 6.8 got a water temp and left it on 63 degrees so my water only climbs to 6.3 now and I adjust every morning
 
Don’t chase PH like that. What I do for hydro is adjust to 5.5 then let it swing up to 6.5 before I adjust back down again. This process of PH adjusting should take place over 2-3 days. You don’t want to adjust daily.
 
I agree with Toker1, don't chase the pH, especially when it is within the range of 5.5 to 6.5. Different nutrients are absorbed by the plants at different pH levels, so it it beneficial to the plants for the pH to vary some what. One can (and I speak from my nearly killing my plants during the second grow!) do damage to the plants by dumping too much pH up or down in the reservoirs to maintain a 'steady' pH level.
 
hey Toker,

its a "new-ish" system... it's been in use for about a year now.
I started a new grow in December, had lights on 24/0 for 12 weeks in Veg while I was training & quadlining two plants.
in those 12 weeks pH never really varied by much, about +- 0.3 of 6.0 over a week time

back last summer I also had an issue with pH dropping by a lot over a couple of days... when I had 4 plants growing.
Used H2O2 then... but never had the idea that CO2 might be a factor.
 
Quick update.

Yesterday evening just before lights out, pH was 5.8. Just to be sure I added 2ml of pH up to the system in case the pH would drop again overnight (didnt get the chance to measure pH after that).

Came home this afternoon and checked, after 19 hours pH is 6.5.

Air pump inlet from outside the tent seems to be working well so far.

Water change tomorrow - Will see what happens!
 
Wow I was really high when I put that up and fked up so many words lmao but naw I adjust as needed if it get out of control as my water chiller keeps my water at 63°F so my water pH normally stays their takes about 3 to 4 days to climb to 6.3 from the original 5.5 I leave it at with the res change so normally it's stay 6.3 pH intill the next res change if I for get to turn on the water chiller tho my pH climbs to like 8.4 in 8 hours no idea why I'm guessing because water temps hit 90° to 100° but I don't know
 
Today's water change details....

pH = 6.2 after settling,
ppm = 980 (EC = 1.96)

entering week 3 of flower... (lights switched to 12/12 on the 9th)

on roughly 5.82 US gallons (22L)
92ml Silicon 15ml CalMag 30ml Micro 15ml Gro 30ml Bloom
Temp @ 19C & RH 48%

Air pump taking in air from outside the tent since 20th march.

Also did some leaf cutting... plants were getting bushy....
 

Attachments

  • photo75047.jpg
    photo75047.jpg
    1.2 MB · Views: 0
  • photo75048.jpg
    photo75048.jpg
    1.1 MB · Views: 0
Air dissolved CO2 has very low abilities to change solution ph specially at higher EC. Respiration and electroneutrality are the main reasons of ph change. Indoor plant tend to grow equally well between ph 5.2-6.3(or even 5.2-7.5 with chelated form of iron) if each specific nutrient in the solution do not become a limiting factor.

Forms of carbon including carbonates and bicarbonates(like baking soda) and also organic acids(like citric acid) are ph buffering agent and can resist against ph change. The 1st two forms increase ph when they are added to the solution and the last one decrease ph. Adding more buffering agent to the solution prevent ph fluctuation.

​​​​​


last thing i like to mention is that mililiter per liter is about the volum not mass. and it is a wrong way to ​​report concentration. The concentrations can not be calculated without knowing the solution percentage.
 
Hi @Iammygod,

I agree with you that 'reporting' concentrations as X ml to Y L is a wrong way, its not presice as it does not specify the molecular mass per volume of each nutritional element added.

However, as I'm using the DWC feeding schedule from GWE (which gives volumes in ml/Gal for nutrients), I've made a spreadsheet to give me the needed volume for nutrients based on the volume of water in my system.
https://www.growweedeasy.com/sites/...eed-General-Hydroponics-nutrient-schedule.pdf

This is the reason i'm stating X ml Micro/Gro/Bloom for Y litres of water.

I'm using the flora trio series of nutrients, (micro for hard water). If you're interested, I can let you know what is inside each 1L bottle in order to work out how much of each nutrient is being added.

The pH down solution that I'm currently using is also by GH, and its made of "81% food grade" phosphoric acid.
My experience with this pH down solution is that it needs a while to stabilse to the desired level - typically several hours.

As for the CO2 idea...

Plant respiration -> added CO2 concentrations in tent,
air pump sucks that in, bubbles the extra CO2 into the water.
air pump does 35L/minute, 4 airstones in total.

only over the last two weeks with the plants in flower, has this issue with the pH dropping quickly come up.

CO2 is heavier than air, but with the ventilaton happening, that CO2 would be rising upwards as the air in the tent is refreshed.

it would seem, that the placement of the airpump in the tent might be a factor in this case....
Or, as I've been seeing over the last few days, having the airpump draw fresh air from outside the tent.
 
Forget that CO2 and air pomp position. They are truly not the reason. Because of chelated forms of iron No need to lower ph when it is 6.5. Your problem is water acidification but you are adding more ph down. contradictory! How are your plant? Are they healty? What source of water do you use?


​​​​​

​​


​​​​​
 
Iammygod,

I added a bit of pH down this time because I've seen that the pH is much more stable now that the airpump is getting air from outside the tent.
Over the last week I did not add any pH down due to the observation that pH kept dropping by a large amount during the lights out period.

Water I use comes from a private well.
starting values for ppm = 290 / pH = 7.4

The plants.... I defoliated them yesterday and they are healthy.
See pics attaced

Please see the details below for the Flora Trio that I use, with CalMag additive and Si+ (All bottles I have are 1L):

CalMag additive:
Nitrogen – 2.9%
Magnesium Oxide (MgO) - 2.5% (1.5% Mg)
Calcium Oxide (CaO) - 5% (3.6% Ca)
Iron (Fe) chelated by EDTA - 0.04%

Flora Micro (Hard water) / NPK 5-0-1
Total Nitrogen (N) - 5%
Ammoniacal nitrogen - 1.5%
Nitrate nitrogen - 3.5%
Soluble potassium (K[SUB]2[/SUB]O) - 1.3%
Boron (B) - 0.01%
Calcium (CaO) - 1.4%
Copper (Cu) Chelated EDTA - 0.01%
Iron (Fe) Chelated 6% EDDHA – 11% DPTA - 0.12%
Manganese (Mn) Chelated EDTA - 0.05%
Molybdenum (Mo) - 0.004%
Zinc (Zn) Chelated EDTA - 0.015%

Flora Gro / NPK 3-1-6:
Total nitrogen (N) - 3%
Ammoniacal nitrogen - 1%
Nitrate nitrogen - 2%
Phospohoric anhydride (P[SUB]2[/SUB]O[SUB]5[/SUB]) - 1%
Potassium oxide(K[SUB]2[/SUB]O) - 6%
Magnesium Oxide (MgO) - 0.8%

Flora Bloom / NPK 0-5-4:
Available Phosphate (P[SUB]2[/SUB]O[SUB]5[/SUB]) - 5%
Soluble potassium (K[SUB]2[/SUB]O) - 4%
Magnesium Oxide (MgO) - 3%
Soluble sulphur (SO[SUB]4[/SUB]) - 5%

Essentials Silicon+ (4ml/L) : ( I can only find the spec for Vitalink Essentials Silicone Max - at 6% - dosage 1ml / L)
SiO2 - 1.4%
 

Attachments

  • photo75100.jpg
    photo75100.jpg
    1 MB · Views: 0
  • photo75101.jpg
    photo75101.jpg
    1.2 MB · Views: 0
Update:
before lights out, pH was 6.0
this morning its was at 5.4

I've drained off 5L of water and replaced it with 4L of premixed nutrient water which was at pH 7.4

system is now at pH 6.4 , ppm 940.

trend is that ppm is falling slightly as well.

Been reading up on factors that influence pH,

A very plausable reason that pH is dropping comes from here: https://www.maximumyield.com/the-top...f-whack/2/3240
"For example, when a plant absorbs potassium ions, it gives off hydrogen ions that lower the pH."
Potassium is the K in NPK.

With my water volume being relatively small at ~ 6 US Gallons for 2 plants, could high potassium uptake be the reason for the fast drops in pH overnight?
 
Last edited:
You must log in or register to reply here.
Back
Top