GrowWeedEasy.com
You're browsing as a guest. Sign up to join the conversation, share your grows, and get help from thousands of fellow growers — it's free and takes less than a minute.
Time to show your grow.
- Thread starter Mr.furley
- Start date
Going2fast
New member
Frostalicious!!! Quikz and slapz are both strutting.
Going2fast
New member
FurnaceBoi
New member
Seed momma is busting to flower. Planted in early December. Giving the clone 1 more week. This will be a nice tent.
the clone was topped at cutting. An experiment. I only got 30% root rate on pre topped clones and they took almost 3 weeks but for my little tent, I'll take the head start at 30%.
next crop I'll do 6 3 gallon or 3 5 gallon.
Learning my space and always improving.
the clone was topped at cutting. An experiment. I only got 30% root rate on pre topped clones and they took almost 3 weeks but for my little tent, I'll take the head start at 30%.
next crop I'll do 6 3 gallon or 3 5 gallon.
Learning my space and always improving.
Attachments
Last edited:
Indelacio
New member
Seedsman's purple ghost candy, at various stages of development. A lot of pics but I think this one turned out well.
Attachments
Bluey
Well-known member
From youngest to oldest, all in the same room with same environment
OZ x SD ..... clones cut 18 hours ago. pH went from 5.8 to about 6.8 in that time. Doing well. Aeroponics low pressure cloner.
One of my sativas I think.... photo, bit light on N
WW x SD .... photo, topped yesterday
OZ x SD .... photo cut to bits yesteray and its first chop no previous training, it was huge
4 autos from Franklin, AK47 x Red CBD
Front left moderate Cal deficiency and the worst but its packing on the most of all main colas
Front right was chemically topped at the first node. Healthy but slow. Most bud sites because of topping.
Rear left the slowest and smallest, with N toxicity
Rear right doing well
OZ x SD ..... clones cut 18 hours ago. pH went from 5.8 to about 6.8 in that time. Doing well. Aeroponics low pressure cloner.
One of my sativas I think.... photo, bit light on N
WW x SD .... photo, topped yesterday
OZ x SD .... photo cut to bits yesteray and its first chop no previous training, it was huge
4 autos from Franklin, AK47 x Red CBD
Front left moderate Cal deficiency and the worst but its packing on the most of all main colas
Front right was chemically topped at the first node. Healthy but slow. Most bud sites because of topping.
Rear left the slowest and smallest, with N toxicity
Rear right doing well
Attachments
Last edited:
Bluey
Well-known member
Mines a 5gal bucket also with 1.5gal nute mix to properly cover the pump. I'm going to put 4 more holes in the top with 3 for clones and 1 to test for pH and add the pH down...the lid is tight and I don't like removing it. I brought the power for the pump and two airlines through the side right at the top. I didn't put a purpose built vent in it, no need.
I have enough equipment to make a second one.
Edit. I'll be transferring to coco from the bucket. Just wondering how long I can keep them in the cloner for....I want to keep a few dormant if I can
I have enough equipment to make a second one.
Edit. I'll be transferring to coco from the bucket. Just wondering how long I can keep them in the cloner for....I want to keep a few dormant if I can
Last edited:
Rootsruler
New member
I have a smaller bucket I want to convert into an auto cloner. Since you both have experience with your DIY autocloners do you think it would be better to go with a 5 gal bucket or the smaller one I have. I think it's a 3 gal bucket. Rather than use the stock 2" collars I'm thinking I can either locate 1" ones or make my own but I want to use the 1" collars so that I can have more sites on the lid and I don't see the need for so much space to clone a cutting or will the closer spacing entangle the roots?
Bluey
Well-known member
I think 1" collars could work. You need to attach the collar ideally before final cutting and dipping the stem. I think it will get very crowded though with possibly tangled roots.
I made the collars myself using a roll of foam and just slowly put the 2" holesaw through it. My pump & spray manifold was a bit high for a 3gal bucket and a 5gal bucket gives me more nute mix and longer roots. I tapped the manifold using the brass threaded misters thread in my drill chuck then put the plastic thread in that...the plastic thread on the plastic misters is not strong enough to tap the white upvc pressure pipe.
The pH goes up very fast with the airstones in there. I'm running the airstones 10min on 10min off to try and slow the pH rise..might even reduce it more.
I made the collars myself using a roll of foam and just slowly put the 2" holesaw through it. My pump & spray manifold was a bit high for a 3gal bucket and a 5gal bucket gives me more nute mix and longer roots. I tapped the manifold using the brass threaded misters thread in my drill chuck then put the plastic thread in that...the plastic thread on the plastic misters is not strong enough to tap the white upvc pressure pipe.
The pH goes up very fast with the airstones in there. I'm running the airstones 10min on 10min off to try and slow the pH rise..might even reduce it more.