After see this weeks article on reptile heating mats, it got me thinking about root zone temperatures again. I've had years of successful grows but always looking to improve. My grow room is in the basement with a concrete floor. I always keep air ports raise off floor but have wondered if root zone is still a little cool for optimal growth, especially with air intake blowing across damp air pots. Have thought about using reptile heating pad to help keep root zone warmer but just haven't pulled the trigger. What do you guys think?
GrowWeedEasy.com
You're browsing as a guest. Sign up to join the conversation, share your grows, and get help from thousands of fellow growers — it's free and takes less than a minute.
Reptile heating mat
- Thread starter PuravidaC
- Start date
3Berries
New member
I rigged up some bucket heaters this fall. They are working great. Still learning the fine details of them but basically It's a length of 4" Flexwatt heat tape and connectors with a two heater temp controller. Then wrapped in some insulation.
My flower room runs mid 50fs with lights out and near 75F lights on this time of year with constant ventilation. I figured an outside plant has it's roots in relatively stable temps all the time unlike the upper part. I am using plastic buckets and saucers so didn't want to use a heat mat as there is no direct contact with the bucket bottom, might interfere with drainage if it did.
Easy make, wrap around and use some tape to secure.
I had an Inkbird controller and tried to run two heaters off one, no good. And the Inkibird probe ws not water poof enough so I got a dedicated two heater controller with water proof probes. The probes need to be deep enough to be in constant moisture. They should also be about 1/3 the way in from the edge. I run them at 73F on and 74F off. ~20 watts each at 110v for 4 foot strip.
A youtube on how to connect the connectors.
https://www.youtube.com/watch?v=q4IhEI6xRqc
Official directions!!!!
https://cdn.shopify.com/s/files/1/0442/8753/files/Flexwatt_parallel.pdf?46321531 24885612981
[url]https://cdn.shopify.com/s/files/1/0442/8753/files/Flexwatt_connectors.pdf?463215 3124885612981[/URL]
https://cdn.shopify.com/s/files/1/04...73243613657645
My flower room runs mid 50fs with lights out and near 75F lights on this time of year with constant ventilation. I figured an outside plant has it's roots in relatively stable temps all the time unlike the upper part. I am using plastic buckets and saucers so didn't want to use a heat mat as there is no direct contact with the bucket bottom, might interfere with drainage if it did.
Easy make, wrap around and use some tape to secure.
I had an Inkbird controller and tried to run two heaters off one, no good. And the Inkibird probe ws not water poof enough so I got a dedicated two heater controller with water proof probes. The probes need to be deep enough to be in constant moisture. They should also be about 1/3 the way in from the edge. I run them at 73F on and 74F off. ~20 watts each at 110v for 4 foot strip.
A youtube on how to connect the connectors.
https://www.youtube.com/watch?v=q4IhEI6xRqcOfficial directions!!!!
https://cdn.shopify.com/s/files/1/0442/8753/files/Flexwatt_parallel.pdf?46321531 24885612981
[url]https://cdn.shopify.com/s/files/1/0442/8753/files/Flexwatt_connectors.pdf?463215 3124885612981[/URL]
https://cdn.shopify.com/s/files/1/04...73243613657645
golfnrl
Well-known member
Speaking of the reptile heat mat mentioned by Nebula. I bought one. Noticed in the instructions that it needs to be mounted on glass and should not be in contact with anything else on the heat side of the mat. It's still in the box. I'm a few weeks away from germinating new seeds and want to use the heater. I can buy a piece of glass from the local hardware store but am wondering if anyone has a different solution.
