What's new
By:
GrowWeedEasy.com
You're browsing as a guest. Sign up to join the conversation, share your grows, and get help from thousands of fellow growers — it's free and takes less than a minute.

DIY Cold Air Intake for Air Pumps

ocgreen

ocgreen

New member
I am struggling with 5 gallon bucket reservoir temps and considering a cheap DIY solution:

Running a 1/2" hose from the intake for each of my 950 GPH air pumps to the inside of a beer fridge freezer. The thought is that I could drill a 1/2" hole for each intake hose and seal with silicon or expanding foam as needed. The hose would pull cold air from freezer to attached air stones, and logically I feel like this should drop temps by a few degrees.

Anyone tried something like this? I see some DIY options where you put a couple hundred feet of hose in a freezer/fridge and the water cools as it travels through; I'm looking for a simpler approach.

Anyone think of any health/safety issues with above idea?

Thanks for taking the time to read my post.

(I know that using a larger tote helps stabilize temp, ph, etc. I'm also looking at building a little cover/shade for my buckets which would reduce amount of light hitting them.)
 
Nice idea, in this last month i was trying to figure out how to put my air pump outside of the window so i can bring the cold air directly to resevoir but the idea of long connection hoses from air pump to airstones may cause a problem prevent me to do so. Cause the air pump which im using lowers the air pressure in time and i turn it of by turning the on/off wheel and after i press more on off side it makes some noise like the release of the pressure and when i turn it back up it continues working like brand new wit a lot of bubles in water.

can u add pictures of the system

peace
 
That’s is an inefficient way to chill the water. Your heat pump will be working harder than what work actually goes into cooling the water. In other words, you will be spending more on electricity than what is needed to get the job done properly. Why not get an actual water chiller? I believe you will save $$ in the long run (when considering operational costs) if you invest in one.
 
I have tested this in the past, pulling air from my keg cooler fridge. What I found is the volume of air moving through the pump from the fridge was not enough to overcome the heat generated by the pump. There was a modest decrease of temp coming out of the pump, but not sufficient to cool the water. The small air chillers were the next option and if mounted away from the room and temp differential is adequate it does a great job. Those are fairly cheap and easy to plump. Did not work for me because of where I live and the space I grow. So... when its hot, I put my grow toys up and fish. :-)
 
I haven't built this yet. I was just doing some brainstorming and thought of drilling into a mini fridge/freezer combo I can pick up for less than $50.
 
Yeah I guess I need to look into where I can find an affordable chiller. First few options I saw were over $500.
 
Thanks for confirming. Any specific small air chillers you would recommend?

This year I'm planning to grow through summer but next year I may shut down shop and get out there on the lake as well. 👌
 
I failed to mention, do not use the hose included, get replacement black one. Took no time at all for alga to grow in the clear one.
 
Toker1 I think you may have sent me that link a while ago, and it works. Just need the area you have the chiller in, cooler than your grow area. For a fact though it will decrease temps, but it has limits.
 
Yes, agreed... when temps get over 85F. My little chiller 72w has a tough time. Luckily for me that rarely happens. That’s why I suggested the 100w model.
And yes... almost forgot (great post below) the clear tube sucks. Be prepared to blacken it out or replace with a black one.
 
Howdy ocgreen, I keep my reservoir temperatures between 62°F and 70°F by using a 0.7 L ice bottle suspended into the reservoir (using an open bottom 3 3/4 inch net pot). Depending on the ambient temperature, the ice bottles usually last 4 to 6 hours between changes. Here's an old photo of the reservoir, the net pot (with the cover on it) keeps the bottle from floating away, requiring the top to be lifted for removal.
 

Attachments

  • photo47835.jpg
    photo47835.jpg
    138.6 KB · Views: 0
Hey DW2 you're helping me out all over the place today.

For my larger totes I'm finding the bottles are really effective. It's the 5 gallon buckets that heat up way too fast.

On one hand, I like how easy it is to do maintenance on the smaller buckets and you can move them around the tent easier to adjust canopy. Reservoir change for large reservoir was stressful!

On the other hand, the smaller reservoir temp spikes from 20C to above 25C overnight and I'm getting more ph fluctuations.

One thing I noticed about your approach is you're using larger bottles. So maybe that's something I can try. Maybe that extra bit to keep it frozen/cool overnight.

One thing I'm realizing... If i need to get a 70-100w chiller for every single bucket then it seems like we're getting into quite the electric bill. Can totally see why people shut down their space for the hot months (assuming you grow yourself enough to last).
 
Thanks all. They're a bit pricier north of the border but still much cheaper than the $500+ units I saw originally.

My main concern with this approach is that if i need one of these for every plant/bucket it seems like it would be a crazy amount of energy used... and wires/mess.

Now I'm starting to wonder if the most effective approach is to dramatically cool the room tents are in by using portable air conditioner. If I can get room cold enough then the air going to bubbles would be cooler and the cold air intake to tent would be cooler as well.

Or maybe I just need some type of inexpensive cover for my buckets while canopy develops. I read that bucket temp because easier to control once you have a full canopy.

Appreciate the tip about hose colour. If I do go this route, and I may buy one to try, I wouldn't have realized that until it was too late.

Thanks again
 
Thanks guys. You both gave me a lot of good info to consider. Think I may pick just one up to see how it works and go from there.
 
I sure hope you can concoct a home made solution to your problem. I could not: frozen water bottles didn't do much at all for me except melt really fast. so I ended up buying chillers for both my grow boxes, which keep the water at 67-68 degrees. First I had to deal with a bout of root rot from hell, and after that I got the chillers, which have been pumping away without a problem ever since.

This ain't no cheap hobby.
 
Besides making a DYI shell and tube heat exchanger (aka a make shift water chiller), only other way I could think of is dig a deep hole in the ground, place the reservoir in the ground and pump the cool water up to your grow room. Geothermal cooling technique.
 
You must log in or register to reply here.
Back
Top