Search results

Topped the WW x at the 3rd node on 6th node growth. Cleaned up the rest

Built a low pressure cloning bucket. 5 cuts from OZ x PPFD 110 pH 5.8 EC 0.3 Sprayer off 20min on 1 min dual air stones Removed fan leaves temp 25⁰C RH 54% Cut on angle removed little strip's of skin above cut, dipped in cloning agent OZ x , been given a huge haircut, EC back up to 1.5 will...

Here's mine

Moved the room around a bit today for better light across the young photos. Finished the aeroponics cloner, currently running 25% iso diluted with water, fire extinguisher on standby, through it. They are not misters but more droplets that spray, didn't have the pressure off the pump to run the...

About to give this a run with some small and large cuttings. Using low pressure misters with an airstone. I'll dip on cut into a (hardwood or softwood?) clonex solution and I plan on just using coco specific veg nutes at about 0.2 to 0.3 EC with around 100 PPFD of all spectrum light. Any...

Bit of training, just pulling them apart Nice to see the buds forming with a little bit of depth.

Gave 2 a trim today..mostly lollipopped, the mutant and the tallest one Left the one in the back corner alone. Still hasnt recovered from N toxicity but the buds are growing slowly, top bud is the slowest and worst. Flower +Si to 2.1 EC 38 DLI Didn't touch the other one, showing a bit...

The slow one with the N toxicity appears to be slowly recovering rather than dying so that's good. I dropped the calmag with the N from its diet and increased the flower nutes to EC 2.1 pH 6.2. I didn't flush as I didn't want to shock her too much The other 3 are doing great, one is showing a...

EC bloom 1.6/1.7 calmag to 1.9 on the 4 autos EC veg & calmag to 1.6 on the large photo ​EC veg & calmag 0.8 large seedling photo EC veg 0.4 tiny seedling (mutated photo) All with silica at same ratio of base nutes DLI autos 40 to 44 DLI photo about 42 Large seedling PPFD 370 Tiny seedling...

Still got problems with the bud leaves, likely N toxicity, definitely not wind, heat or light burn. The above is of 1 plant, far rear LHS. Its the 1 of 4 autos that has struggled the most, its behind on growth throughout the grow. The 3 other autos are going well, only 1 of them showing the...

There's 4 plants I did on an 8 x 5 net Gingerbeard last May. It's really convenient.

Problem thread here https://forum.growweedeasy.com/forum/growing-community/616827-ratty-looking-early-buds#post617022 DLI 40 to 42 on autos EC 1.9 bloom w/silica & calmag DLI on front photo 34 (PPFD 640) EC 1.6 veg w/silica & calmag Advanced seedling 320 PPFD EC 0.5 Little sativa 275 PPFD EC 0.4

Grow thread here https://forum.growweedeasy.com/forum/growing-community/612627-frankie-goes-to-hollywood

On the mend. Almost there

You can see below that the humidity went to the shit but temps are logged as constant. Weird. I am not really sure why. Anyway.

Getting worse So I think I know the problem. I've had both lights at 100% for even spread, it's been hot outside. I'm trying to keep temps a bit closer to 75⁰F than 80⁰f because of the seedlings so AC is running heaps causing VPD around 1.2/1.3. Too high. The best thing for me to do is...

These are buds on two auto plants and not just the top ones..looking a tad shagged out. Pic taken 8 hrs after lights on and I've watered it a few times until I got a bit of runoff. They were looking the same at lights on prior to watering. I raised the light, was 45 DLI now low 40's. Any ideas...

Day, umm, well it's all over the place. The 4 at the back are the autos RED CBD x AK47....drinking heaps. Will be on full flower nutes come end of the week The fat centre front is an Orange Zkittles x Sour Diesel photoperiod, also drinking heaps. Topping it this week for cloning. It will be a...

Yep. Teflon this one and she's already turned back up but it should stop the stretch And one I did a couple of weeks back, the chemically topped mutant, no tape, just support. Split down the middle at the node as usual when topped too close to the node.

Supercropped the tallest one, just the main stem. Only required a few gentle squeezes and it just fell over, but it split length ways, bummer.